AS-EP

Module for capturing 4 damper blade end positions (volt-free)

The module is used to connect the control system with the components

  • Integral AS-Interface slave
  • Monitoring of signal receipt
  • With short circuit protection
  • Easy wiring due to flat cable insulation displacement connectors ('click and go')
  • Certified motor control modules for safe communication up to SIL2
  • Special modules for dampers with special functions including redundant voltage supply
  • Universal module for the connection of various terminal units such as fire dampers, smoke protection dampers or duct smoke detectors

AS-EP 00134585_0
  • Application

Application

  • Connection of up to four limit switches: Damper blade position CLOSED or OPEN for 4 fire dampers, or positions CLOSED and OPEN for 2 fire dampers
  • Integral AS-Interface slave
  • Monitoring of signal receipt
  • Supply voltage to the module through the AS interface
  • Wiring of the limit switches with terminals; PG glands for cable penetration
  • Up to 30 m cable length between module and limit switch
  • Connection with flat cable insulation displacement connector

Technical information

  • Function
  • Technology
  • Specification text
  • Order code
Connection of limit switches 00105189_0..

① Mechanical switch
② 3-wire cable
③ PNP sensor
Screw-fixing the top part to the base creates a safe electrical connection.

DescriptionAS-EP
Electrical design4 inputs
Supply voltage26.5 – 31.6 V DC
Current consumption< 80 mA
Inputs
SwitchingPNP
Sensor voltage supplyAS-i
Voltage range20 – 30 V DC
Max. current load (total for all inputs)160 mA
With short circuit protectionYes
Switching level – high signal 1> 10 V
Input current high/low> 5/< 1 mA
Status display
OperationLED green
FunctionLED yellow
Ambient temperature–25 to 85 °C
Protection levelIP 67
AS-i profileS 0.0
I/O configuration0 Hex
ID code0 Hex
EMCEN 50081-2; EN 50082-2
Casing materialsPBTP (Pocan)
Dimensions L × B × H102 × 45 × 70 mm
ConnectionContact pins on FC or SC lower module
Data bitsData bit I allocation: D0 I – 1, D1 I – 2, D2 I – 3, D3 I – 4


Standard description (characteristics)

  • Module for capturing 4 damper blade end positions (volt-free)
  • Integral AS-Interface slave
  • Monitoring of signal receipt
  • Flat cable connection
  • Supply voltage to the module through the AS interface
  • Make: TROX GmbH or equivalent
  • Type: AS-EP

00135241_0
 

 Module
AS-EPR       Module for the connection of four limit switches
AS-EM       Module for controlling an actuator
AS-EM/EK       Module for controlling actuators on smoke control dampers
AS-EM/SO       Module for controlling actuators with special functions
AS-EM/SIL2       Module for controlling actuators with SIL2 certificate
AS-EM/C       Module for universal control functions, 2 outputs, 4 inputs
TNC-A005S       AS-i safety input module
TNC-Z0094       Relay module 4E/4A
TNC-Z0047       Illuminated push button module

 

Share page

Recommend this page

Recommend this page by sending a link by mail.

Fields marked with an (*) are required fields.

Share page

Thank you for your recommendation!

Your recommendation has been sent and should arrive shortly.


Contact

We are here for you

Visual contact Visual contact

Please specify your message and type of request
Tel.: +49 (0)2845 / 202-0 | Fax: +49 (0)2845/202-265

Fields marked with an (*) are required fields.

Contact

Thank you for your message!

Visual contact Visual contact

Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +49 (0)2845 / 202-0 | Fax: +49 (0)2845/202-265

Contact

We are here for you

Visual contact Visual contact

Please specify your message and type of request
Tel.: +49 (0)2845 / 202-0 | Fax: +49 (0)2845/202-265

Attachment (max. 10MB)

Fields marked with an (*) are required fields.

Contact

Thank you for your message!

Visual contact Visual contact

Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +49 (0)2845 / 202-0 | Fax: +49 (0)2845/202-265